EDATEC Low-power SBC based Raspberry Pi CM0 - NANO-10000

Single-Board Computer Based on Raspberry Pi CM0

Specifications

System  

• CPU: 1GHz quad-core 64-bit Arm Cortex-A53 processor  
• VPU: H.264/MPEG-4 video decoding, 1080p@30fps, H.264 encoding, 1080p@30fps
• GPU: OpenGL ES 1.1/2.0 graphics processing  
• Memory: 512MB SDRAM  
• Storage: 8GB or 16GB eMMC storage available
  Micro SD card slot (When the CM0Lite is used, a Micro SD card can be inserted for system boot)

Software

• Operating System:
  • Raspberry Pi OS (Desktop) 64-bit
  • Raspberry Pi OS (Lite) 64-bit
  • Raspberry Pi OS (Desktop) 32-bit
  • Raspberry Pi OS (Lite) 32-bit

Panle I/O  

• RTC Battery Base: 1 x RTC Battery Base, allows for the installation of an RTC battery (CR2032) through this interface 
• DIP Switch: 1 x DIP switch, supports switching between normal operation mode and flashing mode.
  • LD (switch positioned toward the RTC battery base): Flashing mode
  • RUN (switch positioned toward the reset button): Normal operation mode (default state)
• Power: 1 x DC input, USB Type-C connector, supports 5V input
• HDMI: 1 x HDMI port, Type-A connector, compliant with HDMI 1.3a standard, supports 1080p resolution at 30Hz
• USB 2.0: 2 x USB 2.0 ports, stacked Type-A connector, each supporting a maximum data transfer rate of 480Mbps 
• 100M Ethernet: 1 x adaptive 10M/100M ethernet port, RJ45 connector. It can be used to access the network 
• Micro SD Card Slot: 1 x Micro SD card slot, supports installation of a Micro SD card for system boot.
  Note: The Micro SD card slot is only compatible with the CM0Lite

Buttons and Indicators  

• PWR: 1 x red power indicator, used to display the device's power on/off status
• ACT: 1 x green system status indicator, used to monitor the device's operating status
• RESET: 1 x reset button, recessed design, pressing the button restarts the device

Expansion I/O  

• PoE HAT Header: 1 x PoE HAT Header, 2x2-pin 2.54mm pitch header, supports expansion connection for Raspberry Pi PoE HAT module
• IPEX-1 Interface : 1 x IPEX-1 interface, supports connection to an external antenna
• Raspberry Pi 40-Pin GPIO Header: 1 x Raspberry Pi 40-Pin GPIO Header, 2x20-pin 2.54mm pitch header. Pin definitions include GPIO2-GPIO27, 2x 3V3, 2x 5V, 1x ID_SD and 1x ID_SC, supports connection with Raspberry Pi standard accessories
• 4-lane CSI Interface: 1 x 4-lane CSI Interface, 22-pin FPC connector, compatible with Raspberry Pi Camera modules
• 4-lane DSI Interface: 1 x 4-lane DSI Interface, 22-pin FPC connector, compatible with Raspberry Pi Touch Display
• USB 2.0 Interface: 1 x USB 2.0 interface, 1x5-pin 2.54mm pitch header. Pin definitions: VBUS/USB_DM/USB_DP/GND/NC, supports expansion of USB 2.0 interface
• 10-Pin Header: 1 x 10-Pin Header, 2x5-pin 2.54mm pitch header. Pin definitions: 4xGND/RUN_PG/WL_ON/BT_ON/TV_OUT/RUN_PG_BUF/GLOBAL_EN, reserved for future functions.
  • Short GND (Pin 1) and RUN_PG (Pin 2): Shuts down the ED-CM0NANO
  • Short GND (Pin 3) and WL_ON (Pin 4): Disables Wi-Fi functionality
  • Short GND (Pin 5) and BT_ON (Pin 6): Disables Bluetooth functionality
  • Connect a button between RUN_PG_BUF (Pin 9) and GLOBAL_EN (Pin 10): Can be used to wake the ED-CM0NANO from sleep mode

Expansion Functions  

• RTC: Integrated RTC function with an RTC battery base, supporting the installation of a CR2032 battery as RTC backup power
• Watch Dog: Built-in Watch Dog function, enhancing system reliability

Electrical Characteristics

• Input Voltage: 5V DC, Note: A 5V 3A adapter is recommended
• Power Consumption:10W (Max)

Mechanical Characteristics

• Dimensions: 100mm x 85mm (WxD)  
• Weight: About 52g

Wireless

• Wi-Fi/Bluetooth (optional): Supports 2.4GHz Wi-Fi and Bluetooth, with an external FPC antenna.
  • 2.4GHz Wi-Fi: Compatible with IEEE 802.11 b/g/n
  • Bluetooth 5.0: Compatible frequency band 2402MHz ~ 2480MHz

Environmental & Regulatory  

• Operating Temperature: -20°C ~ 60°C   
• Storage Temperature: -20°C ~ 60°C  
• Ambient humidity: 5% ~ 95% (non-condensing)